It should be fully opened when cleaning the sterilizer. And enzymes are quickly killed. The vertical pipe of the circulating storage tank should be connected to the trench stainless steel beer tank manufacturers to prevent the washing liquid from corroding and damaging the floor of the workshop. At the steam inlet,The feed pump must ensure the correct rotation direction of the motor.
The discharge is controlled by a throttle valve, which can make the boiling point of the material higher than the maximum temperature while maintaining a certain pressure. Four supporting bolts can be adjusted during equipment installation, and the supporting feet must be in contact with the floor. During normal production, adjust this valve, the back pressure is generated by the driving force of the pump to overcome the spring pressure to control the flow. The 4 feet of the feed pump are also required to be in contact with the floor, and the pump shaft must be leveled to prevent vibration when the equipment is in use.
After passing through a high-temperature barrel filled with high pressure, the materials are quickly heated to the sterilization temperature and kept for about 3 seconds before and after. 3. 8. All pipes connected to this equipment should be protected from external forces, especially the effect of thermal expansion should be eliminated.The ultra-high temperature instantaneous sterilizer adopts a three-way cock, and the flow can be adjusted as required, and it is reliable in use.78MPa (8Kgf/cm2) safety valve must be installed. After installation, the bearing can be turned by hand to see if it is flexible.
The rest of the pipe fittings are prepared by the user. 1. If the next process needs to increase the temperature, it can be achieved by adjusting the angle shut-off valve or circulation, and vice versa, by connecting cooling water to reduce the discharge temperature. Due to the use of stainless steel three-way cock at the same time, the flow can be adjusted appropriately. For factories where a sudden power failure may occur, connect the condensate outlet pipe under the high temperature barrel with a four-way, one end with a trap, one end with a water inlet shut-off valve, and then a tap water pipe, one end with a water shut-off valve, except for accessories.
Below we specifically introduce the installation method of the ultra-high temperature instantaneous sterilizer equipment. Generally, the materials are preheated by pumping them into the heat exchange device of the cold and hot materials in the sterilizer by a centrifugal pump. The operator faces the impeller and the pump shaft should rotate counterclockwise.
The sterilizer is installed on the flat floor in the workshop, without equipment foundation.The circulating storage tank can be used to prepare acid and alkali solutions to effectively clean the scale on the inner wall of the coil. After the material exits the high-temperature barrel, it is cooled by heat exchange with the cold material, and the temperature is generally lower than 65°C.7MPa (150Kgf/cm2) without leakage. When using a high-pressure homogenizer, the user’s self-connected pipeline should be subjected to a pressure test of 14
https://www.nbhrrq.com/product/bright-beer-tank/
The discharge is controlled by a throttle valve, which can make the boiling point of the material higher than the maximum temperature while maintaining a certain pressure. Four supporting bolts can be adjusted during equipment installation, and the supporting feet must be in contact with the floor. During normal production, adjust this valve, the back pressure is generated by the driving force of the pump to overcome the spring pressure to control the flow. The 4 feet of the feed pump are also required to be in contact with the floor, and the pump shaft must be leveled to prevent vibration when the equipment is in use.
After passing through a high-temperature barrel filled with high pressure, the materials are quickly heated to the sterilization temperature and kept for about 3 seconds before and after. 3. 8. All pipes connected to this equipment should be protected from external forces, especially the effect of thermal expansion should be eliminated.The ultra-high temperature instantaneous sterilizer adopts a three-way cock, and the flow can be adjusted as required, and it is reliable in use.78MPa (8Kgf/cm2) safety valve must be installed. After installation, the bearing can be turned by hand to see if it is flexible.
The rest of the pipe fittings are prepared by the user. 1. If the next process needs to increase the temperature, it can be achieved by adjusting the angle shut-off valve or circulation, and vice versa, by connecting cooling water to reduce the discharge temperature. Due to the use of stainless steel three-way cock at the same time, the flow can be adjusted appropriately. For factories where a sudden power failure may occur, connect the condensate outlet pipe under the high temperature barrel with a four-way, one end with a trap, one end with a water inlet shut-off valve, and then a tap water pipe, one end with a water shut-off valve, except for accessories.
Below we specifically introduce the installation method of the ultra-high temperature instantaneous sterilizer equipment. Generally, the materials are preheated by pumping them into the heat exchange device of the cold and hot materials in the sterilizer by a centrifugal pump. The operator faces the impeller and the pump shaft should rotate counterclockwise.
The sterilizer is installed on the flat floor in the workshop, without equipment foundation.The circulating storage tank can be used to prepare acid and alkali solutions to effectively clean the scale on the inner wall of the coil. After the material exits the high-temperature barrel, it is cooled by heat exchange with the cold material, and the temperature is generally lower than 65°C.7MPa (150Kgf/cm2) without leakage. When using a high-pressure homogenizer, the user’s self-connected pipeline should be subjected to a pressure test of 14
https://www.nbhrrq.com/product/bright-beer-tank/
The impurities are intercepted in the filter bag and can be used continuously after replacing the filter bag.Bag filter is a new type of filtration system.This high-speed shock brings direct The consequence is the expansion of the polarization in the brand camp.
In case, the China beer brewhouse manufacturers filter bag can be replaced and used continuously (the filter bag can generally be reused by cleaning). There are many industrial chains in China, the industry’s low concentration of production, low research and development capabilities for high-end products, and low manufacturing technology levels in the bag filter industry still exist.4MPa, the cylinder cover should be shut down and the filter bag should be checked for residue.
Main uses: paint, beer, vegetable oil, medicine, chemicals, petroleum products, textile chemicals, photosensitive chemicals, electroplating solution, milk, mineral water, hot solvent, latex, industrial water, sugar water, resin, ink, industrial wastewater, fruit juice , Edible oil, wax, etc. Excessive filtration pressure will damage the filter bag and the protection net, so special attention should be paid.
With the extension of use time, the filter residue in the cylinder gradually increases. The pressure of the filter is generally adjusted to 0. The bag filter is easy to operate.3MPa, which can be adjusted through the return line or the return valve on the pump. When in use, you only need to install the filter bag of the required fineness level in the filter cartridge, check whether the O-ring is intact, and then tighten the ring bolt of the filter cartridge cover to start work.05MPa. When the pressure reaches 0. After the pump is started, the pressure gauge on the filter rises slightly, and the initial pressure is about 0.
Inside the bag filter, the filter bag is supported by a metal mesh basket. The liquid flows in from the inlet and flows out from the outlet after being filtered by the filter bag. The import and export trade deficit continues to expand.Bag filter is a kind of multi-purpose filtering equipment with novel structure, small size, simple and flexible operation, energy saving, high efficiency, airtight work and strong applicability
https://www.nbhrrq.com/product/brewhouse/
In case, the China beer brewhouse manufacturers filter bag can be replaced and used continuously (the filter bag can generally be reused by cleaning). There are many industrial chains in China, the industry’s low concentration of production, low research and development capabilities for high-end products, and low manufacturing technology levels in the bag filter industry still exist.4MPa, the cylinder cover should be shut down and the filter bag should be checked for residue.
Main uses: paint, beer, vegetable oil, medicine, chemicals, petroleum products, textile chemicals, photosensitive chemicals, electroplating solution, milk, mineral water, hot solvent, latex, industrial water, sugar water, resin, ink, industrial wastewater, fruit juice , Edible oil, wax, etc. Excessive filtration pressure will damage the filter bag and the protection net, so special attention should be paid.
With the extension of use time, the filter residue in the cylinder gradually increases. The pressure of the filter is generally adjusted to 0. The bag filter is easy to operate.3MPa, which can be adjusted through the return line or the return valve on the pump. When in use, you only need to install the filter bag of the required fineness level in the filter cartridge, check whether the O-ring is intact, and then tighten the ring bolt of the filter cartridge cover to start work.05MPa. When the pressure reaches 0. After the pump is started, the pressure gauge on the filter rises slightly, and the initial pressure is about 0.
Inside the bag filter, the filter bag is supported by a metal mesh basket. The liquid flows in from the inlet and flows out from the outlet after being filtered by the filter bag. The import and export trade deficit continues to expand.Bag filter is a kind of multi-purpose filtering equipment with novel structure, small size, simple and flexible operation, energy saving, high efficiency, airtight work and strong applicability
https://www.nbhrrq.com/product/brewhouse/
The emulsification pump is a precise combination of rotor and stator, which generates strong shearing force during high-speed rotation to achieve the purpose of mixing, crushing and emulsification. , Impact tearing and turbulence, etc. The high-speed rotation of the bearing will generate The products to be mixed are crushed, emulsified, and discharged from the bottom of the emulsifying pump.
The external material of the pump cavity is mainly stainless steel model SS316, which is wear-resistant and not easy to rust. The internal structure of the pump cavity is also made of stainless steel, and it is more corrosive and wear-resistant than the outside. Under normal circumstances, the phases are incompatible with each other. When external energy is input, the two materials recombine into a homogeneous phase.
It mainly depends on the support of electricity to convert the electric energy into the power of the high-speed rotation of the bearing. After the cyclic reciprocation of the high-frequency emulsification pump, stable high-quality products are finally obtained . It is widely used in daily chemical, food, medicine, chemical, petroleum, coating, nano materials and other fields.
The emulsification pump makes the immiscible solid phase, liquid phase and gas phase under the combined action of the corresponding cooking process and the appropriate amount of additives, instantaneously uniformly and finely dispersed and emulsified. Emulsification pumps can be used for continuous emulsification or dispersion of multiphase liquid media, and at the same time play a role in conveying low viscosity liquid media. It can also achieve continuous mixing of powder and liquid in proportion.
And to eliminate quality differences between batches, the basic structure consists of a pump cavity and a pair of stators and rotors. Electricity is the source of the power of the emulsification pump. At present, emulsification pumps are widely used.., to form suspension (solid/liquid), emulsion (liquid/liquid) and foam (gas/liquid). In this way, some oxidizing liquids can be better subdivided without causing damage to the pump body. The pump body of the emulsification pump is mainly composed of the outside of the pump cavity and the inside of the pump cavity.
Efficient online dispersing equipment can be installed on the pipeline to continuously process materials. Due to the high tangential speed and high-frequency mechanical effect of the high-speed rotation of the rotor, the emulsification pump causes strong mechanical and hydraulic shear, centrifugal beer brewing equipment factory extrusion, and liquid layer friction in the narrow gap between the stator and the rotor. An emulsification pump is a device that efficiently, quickly and uniformly enters one phase or multiple phases (liquid, solid, gas) into another incompatible continuous phase (usually liquid). The working principle of the emulsification pump is also very simple
https://www.nbhrrq.com/product/fermentation-tank/
The external material of the pump cavity is mainly stainless steel model SS316, which is wear-resistant and not easy to rust. The internal structure of the pump cavity is also made of stainless steel, and it is more corrosive and wear-resistant than the outside. Under normal circumstances, the phases are incompatible with each other. When external energy is input, the two materials recombine into a homogeneous phase.
It mainly depends on the support of electricity to convert the electric energy into the power of the high-speed rotation of the bearing. After the cyclic reciprocation of the high-frequency emulsification pump, stable high-quality products are finally obtained . It is widely used in daily chemical, food, medicine, chemical, petroleum, coating, nano materials and other fields.
The emulsification pump makes the immiscible solid phase, liquid phase and gas phase under the combined action of the corresponding cooking process and the appropriate amount of additives, instantaneously uniformly and finely dispersed and emulsified. Emulsification pumps can be used for continuous emulsification or dispersion of multiphase liquid media, and at the same time play a role in conveying low viscosity liquid media. It can also achieve continuous mixing of powder and liquid in proportion.
And to eliminate quality differences between batches, the basic structure consists of a pump cavity and a pair of stators and rotors. Electricity is the source of the power of the emulsification pump. At present, emulsification pumps are widely used.., to form suspension (solid/liquid), emulsion (liquid/liquid) and foam (gas/liquid). In this way, some oxidizing liquids can be better subdivided without causing damage to the pump body. The pump body of the emulsification pump is mainly composed of the outside of the pump cavity and the inside of the pump cavity.
Efficient online dispersing equipment can be installed on the pipeline to continuously process materials. Due to the high tangential speed and high-frequency mechanical effect of the high-speed rotation of the rotor, the emulsification pump causes strong mechanical and hydraulic shear, centrifugal beer brewing equipment factory extrusion, and liquid layer friction in the narrow gap between the stator and the rotor. An emulsification pump is a device that efficiently, quickly and uniformly enters one phase or multiple phases (liquid, solid, gas) into another incompatible continuous phase (usually liquid). The working principle of the emulsification pump is also very simple
https://www.nbhrrq.com/product/fermentation-tank/
Due to its outstanding characteristics, the emulsification tank has been widely used at present. Under the action of the centrifugal force generated by the high-speed and strong rotating rotor, the emulsification tank throws the material from the radial direction into the narrow and precise gap between the stator and the rotor. If there is no drainage, please notify the equipment power department for maintenance.
Observe the tank temperature gauge and close the shut-off valve appropriately when the temperature exceeds the set value. The volume of the materials must fermentation tank not be less than 5%. At the same time, it is subjected to centrifugal squeezing, impact and other forces, so that the material is dispersed, mixed, emulsification. However, the emulsification tank must be operated in strict accordance with the operating procedures so that it can be completed efficiently.
Emulsifying tanks are widely used in other industries to mix and emulsify materials to improve production efficiency and material quality. Check whether the safety valve is ventilated smoothly and clean with drinking water every shift; 2. Check the pressure of the steam pipe after decompression (less than 0. The machine has the advantages of compact structure, small size, light weight, easy operation, low noise and stable operation.. Add materials first, and it is strictly forbidden to start the tank with an empty tank. Inspection before starting 1.
Adding materials should not exceed 70% of the tank volume, so as to avoid overflow of materials during mixing and cause burns. We will introduce in detail the operating procedures of the emulsification tank. 1. So as not to burn the shaft sleeve of the mixer. Its biggest feature is that it does not grind the medium in the production process, and integrates high-speed shearing, dispersion, homogenization, mixing, and crushing. Check whether the pressure gauges are verified and within the verification validity period.4MPa)
Operation: In one. Open the steam stop valve and adjust it to a suitable opening.We all know about the emulsification tank. If they exceed the verification period, replace the verified and within the verification period. Check whether the accessories of the emulsification tank are running, emitting, dripping or leaking; 3. Turn on the mixing motor circuit breaker and start mixing. Check the trap for drainage
Observe the tank temperature gauge and close the shut-off valve appropriately when the temperature exceeds the set value. The volume of the materials must fermentation tank not be less than 5%. At the same time, it is subjected to centrifugal squeezing, impact and other forces, so that the material is dispersed, mixed, emulsification. However, the emulsification tank must be operated in strict accordance with the operating procedures so that it can be completed efficiently.
Emulsifying tanks are widely used in other industries to mix and emulsify materials to improve production efficiency and material quality. Check whether the safety valve is ventilated smoothly and clean with drinking water every shift; 2. Check the pressure of the steam pipe after decompression (less than 0. The machine has the advantages of compact structure, small size, light weight, easy operation, low noise and stable operation.. Add materials first, and it is strictly forbidden to start the tank with an empty tank. Inspection before starting 1.
Adding materials should not exceed 70% of the tank volume, so as to avoid overflow of materials during mixing and cause burns. We will introduce in detail the operating procedures of the emulsification tank. 1. So as not to burn the shaft sleeve of the mixer. Its biggest feature is that it does not grind the medium in the production process, and integrates high-speed shearing, dispersion, homogenization, mixing, and crushing. Check whether the pressure gauges are verified and within the verification validity period.4MPa)
Operation: In one. Open the steam stop valve and adjust it to a suitable opening.We all know about the emulsification tank. If they exceed the verification period, replace the verified and within the verification period. Check whether the accessories of the emulsification tank are running, emitting, dripping or leaking; 3. Turn on the mixing motor circuit breaker and start mixing. Check the trap for drainage
The production process of draft beer machine has been continuously optimized and developed
2020年9月22日Draft beer machine has a unique sense of balance, interacting with the taste of malt, bitterness of hops, roasting taste and other flavors. From light golden to jet black, the color of draft beer is mainly derived from the different colors of roasted malt.
With the continuous improvement of technology, the production process of draft beer machine has been continuously optimized and developed. The overall equipment and pipeline layout of the draft beer machine is beautiful and elegant, safe and convenient to operate, which can meet more needs of consumers.
Before drinking, only carbon dioxide can be injected through the draft beer machine to avoid direct contact with the air, so the taste is fresher and purer , The foam stainless steel beer tanks manufacturers is richer, and it is more refreshing when drinking. The draft beer is usually injected directly from the production line into a fully enclosed draft beer machine, and the draft beer machine is used to control the wine at a suitable temperature.
The risk of osteoporosis, eliminate muscle fatigue and so on. Finally committed to the research and development, production and sales of beer-related machinery and equipment, through the continuous introduction of advanced production equipment technology, draft beer machine equipment manufacturing technology, research and development of excellent performance draft beer machine equipment.
Draft beer can enhance the function of the digestive system. The alcohol and polyphenols in the beer can promote gastric juice secretion, help digestion, and can effectively prevent cardiovascular and cerebrovascular diseases, promote blood circulation, and have the functions of soothing the nerves and benefiting the brain.
Draft beer machine equipment has made continuous breakthroughs in brewing technology and processing and manufacturing quality, introducing advanced process technology, realizing simulation functions, and maintaining advanced nature
https://www.nbhrrq.com/product/bright-beer-tank/
With the continuous improvement of technology, the production process of draft beer machine has been continuously optimized and developed. The overall equipment and pipeline layout of the draft beer machine is beautiful and elegant, safe and convenient to operate, which can meet more needs of consumers.
Before drinking, only carbon dioxide can be injected through the draft beer machine to avoid direct contact with the air, so the taste is fresher and purer , The foam stainless steel beer tanks manufacturers is richer, and it is more refreshing when drinking. The draft beer is usually injected directly from the production line into a fully enclosed draft beer machine, and the draft beer machine is used to control the wine at a suitable temperature.
The risk of osteoporosis, eliminate muscle fatigue and so on. Finally committed to the research and development, production and sales of beer-related machinery and equipment, through the continuous introduction of advanced production equipment technology, draft beer machine equipment manufacturing technology, research and development of excellent performance draft beer machine equipment.
Draft beer can enhance the function of the digestive system. The alcohol and polyphenols in the beer can promote gastric juice secretion, help digestion, and can effectively prevent cardiovascular and cerebrovascular diseases, promote blood circulation, and have the functions of soothing the nerves and benefiting the brain.
Draft beer machine equipment has made continuous breakthroughs in brewing technology and processing and manufacturing quality, introducing advanced process technology, realizing simulation functions, and maintaining advanced nature
https://www.nbhrrq.com/product/bright-beer-tank/
