It should be fully opened when cleaning the sterilizer. And enzymes are quickly killed. The vertical pipe of the circulating storage tank should be connected to the trench stainless steel beer tank manufacturers to prevent the washing liquid from corroding and damaging the floor of the workshop. At the steam inlet,The feed pump must ensure the correct rotation direction of the motor.
The discharge is controlled by a throttle valve, which can make the boiling point of the material higher than the maximum temperature while maintaining a certain pressure. Four supporting bolts can be adjusted during equipment installation, and the supporting feet must be in contact with the floor. During normal production, adjust this valve, the back pressure is generated by the driving force of the pump to overcome the spring pressure to control the flow. The 4 feet of the feed pump are also required to be in contact with the floor, and the pump shaft must be leveled to prevent vibration when the equipment is in use.
After passing through a high-temperature barrel filled with high pressure, the materials are quickly heated to the sterilization temperature and kept for about 3 seconds before and after. 3. 8. All pipes connected to this equipment should be protected from external forces, especially the effect of thermal expansion should be eliminated.The ultra-high temperature instantaneous sterilizer adopts a three-way cock, and the flow can be adjusted as required, and it is reliable in use.78MPa (8Kgf/cm2) safety valve must be installed. After installation, the bearing can be turned by hand to see if it is flexible.
The rest of the pipe fittings are prepared by the user. 1. If the next process needs to increase the temperature, it can be achieved by adjusting the angle shut-off valve or circulation, and vice versa, by connecting cooling water to reduce the discharge temperature. Due to the use of stainless steel three-way cock at the same time, the flow can be adjusted appropriately. For factories where a sudden power failure may occur, connect the condensate outlet pipe under the high temperature barrel with a four-way, one end with a trap, one end with a water inlet shut-off valve, and then a tap water pipe, one end with a water shut-off valve, except for accessories.
Below we specifically introduce the installation method of the ultra-high temperature instantaneous sterilizer equipment. Generally, the materials are preheated by pumping them into the heat exchange device of the cold and hot materials in the sterilizer by a centrifugal pump. The operator faces the impeller and the pump shaft should rotate counterclockwise.
The sterilizer is installed on the flat floor in the workshop, without equipment foundation.The circulating storage tank can be used to prepare acid and alkali solutions to effectively clean the scale on the inner wall of the coil. After the material exits the high-temperature barrel, it is cooled by heat exchange with the cold material, and the temperature is generally lower than 65°C.7MPa (150Kgf/cm2) without leakage. When using a high-pressure homogenizer, the user’s self-connected pipeline should be subjected to a pressure test of 14
https://www.nbhrrq.com/product/bright-beer-tank/
The discharge is controlled by a throttle valve, which can make the boiling point of the material higher than the maximum temperature while maintaining a certain pressure. Four supporting bolts can be adjusted during equipment installation, and the supporting feet must be in contact with the floor. During normal production, adjust this valve, the back pressure is generated by the driving force of the pump to overcome the spring pressure to control the flow. The 4 feet of the feed pump are also required to be in contact with the floor, and the pump shaft must be leveled to prevent vibration when the equipment is in use.
After passing through a high-temperature barrel filled with high pressure, the materials are quickly heated to the sterilization temperature and kept for about 3 seconds before and after. 3. 8. All pipes connected to this equipment should be protected from external forces, especially the effect of thermal expansion should be eliminated.The ultra-high temperature instantaneous sterilizer adopts a three-way cock, and the flow can be adjusted as required, and it is reliable in use.78MPa (8Kgf/cm2) safety valve must be installed. After installation, the bearing can be turned by hand to see if it is flexible.
The rest of the pipe fittings are prepared by the user. 1. If the next process needs to increase the temperature, it can be achieved by adjusting the angle shut-off valve or circulation, and vice versa, by connecting cooling water to reduce the discharge temperature. Due to the use of stainless steel three-way cock at the same time, the flow can be adjusted appropriately. For factories where a sudden power failure may occur, connect the condensate outlet pipe under the high temperature barrel with a four-way, one end with a trap, one end with a water inlet shut-off valve, and then a tap water pipe, one end with a water shut-off valve, except for accessories.
Below we specifically introduce the installation method of the ultra-high temperature instantaneous sterilizer equipment. Generally, the materials are preheated by pumping them into the heat exchange device of the cold and hot materials in the sterilizer by a centrifugal pump. The operator faces the impeller and the pump shaft should rotate counterclockwise.
The sterilizer is installed on the flat floor in the workshop, without equipment foundation.The circulating storage tank can be used to prepare acid and alkali solutions to effectively clean the scale on the inner wall of the coil. After the material exits the high-temperature barrel, it is cooled by heat exchange with the cold material, and the temperature is generally lower than 65°C.7MPa (150Kgf/cm2) without leakage. When using a high-pressure homogenizer, the user’s self-connected pipeline should be subjected to a pressure test of 14
https://www.nbhrrq.com/product/bright-beer-tank/
コメント